U-SET (User Settings) for HANDHELD CONTROLS - 906 Engineering
2734
page-template-default,page,page-id-2734,theme-bridge,woocommerce-demo-store,woocommerce-no-js,ajax_updown,page_not_loaded,,vertical_menu_enabled,side_area_uncovered_from_content,columns-4,qode-child-theme-ver-1.0.0,qode-theme-ver-9.1.3,wpb-js-composer js-comp-ver-4.7.4,vc_responsive

U-SET (User Settings) for HANDHELD CONTROLS

NOTE: Occasionally, in an effort to improve our aftermarket controls, 906 Engineering will change the settings within the U-SET feature. These instructions are for the handheld User Settings. See the instruction sheet provided with your control for the exact User Settings on your control.

This feature allows the user to customize features on this control to their preferences. Customizable features include:

  • Double Tap
  • Quick Float
  • Automatic Shutdown
  • Soft Stop
  • Factory Reset
  • Shake (for Meyer E-68 Express Straight Blade only)
  • Down Pressure (for SnowEx plows that have Down Pressure)

Handheld U-SET Operation Instructions (using 4 features for this example):

To utilize the U-SET feature, you must enter the U-SET Mode.

  • Turn the control OFF.
  • (Fig. 1) PRESS & HOLD the DOWN button on the keypad (either keypad), then turn the ON/OFF SWITCH to the “ON” position.
  • (Fig. 2) The center LED will turn BLUE, then RELEASE the DOWN button. You are now in U-SET Mode (Channel #0).
  • (Fig. 3) PRESS the “UP” button to scroll up through the different Channels (1-4).
  • PRESS the “DOWN” button to scroll down through the different Channels (4-1).

Channels:

Channel #0 = Programming Home (BLUE)
Channel #1 = Double Tap (blinks one time)
Channel #2 = Quick Float (blinks two times)
Channel #3 = Automatic Shutdown set to 40 minutes (blinks three times)
Channel #4 = Soft Stop (blinks four times)

  • Scroll through the customizable channels to the feature you would like to change. Once there.
  • (Fig. 4) PRESS & RELEASE the “RIGHT” to turn the channel ON (Blinks GREEN)
  • (Fig. 5) PRESS & RELEASE the “LEFT” to turn the channel OFF (Blinks RED)

  • Once you have set all the channels, scroll back to Channel #0 (BLUE). Once there, the control will automatically save your settings (the LED’s will cycle through a pattern).
  • Turn the control’s power OFF (ON/OFF Switch), then back ON to test your changes.

About the Features:

Double Tap Up & Float (Channel #1) Factory Setting OFF (Blinks RED)

A quick double tap of the UP button will automatically raise the plow for 2-3 seconds. And, a quick double tap of the DOWN button will immediately drop the plow into FLOAT.

When Double Tap is turned ON, the plow will immediately drop into FLOAT with a Double Tap of the DOWN button. When using Double Tap, it is recommended that you raise the plow and turn your control OFF (to avoid accidental activation of Float) when driving on the road.

Quick Float or One Touch Float (Channel #2) Factory Setting OFF (Blinks RED)

Pressing the DOWN button once will immediately drop the plow into FLOAT.

When Quick Float is turned ON, the plow will immediately drop into FLOAT with one touch of the DOWN button. When using Quick Float, it is recommended that you raise the plow and turn your control OFF (to avoid accidental activation of Float) when driving on the road.

Automatic Shutdown After 40 Minutes (Channel #3) Factory Setting OFF (Blinks RED)

Changing this setting will the allow the control to remain idle for 40 Minutes (instead of 20) before it automatically shuts down (Blinks RED). To restart the control, turn OFF, then back ON.

Soft Stop OFF or ON (Channel #4) Factory Setting ON (Blinks GREEN)

(This feature does NOT work on all plows, It depends on the plow manufacturer’s valve setup)
The Soft Stop feature is NOT included with the Boss Vee Blade controller.

Turning OFF the Soft Stop feature could cause damage to your plows hydraulic system and may shorten the life of valves and hoses. Excessive banging may occur with certain manufacturer’s plows. Turning OFF the Soft Stop feature is NOT recommended for Meyers/Diamond plows.

….

Factory Reset:

..

Factory Reset (Changes all U-Set Features back to Factory Settings)

To reset all the U-SET features back to the factory settings, anywhere in PROGRAMMING MODE, PRESS and HOLD the “LEFT” and “RIGHT” buttons at the same time for 4-5 seconds. Wait for the LED’s to cycle and the BLUE LED to flash, then RELEASE. Turn the control power OFF, then back ON to test your changes.
NOTE: If running Factory Reset where no changes are made, after 4-5 seconds the BLUE LED will flash. Turn the control OFF, then back ON.

Disclaimer: The use of names of manufacturers is for the assistance of our customers in identifying replacement parts which we manufacture or which may be manufactured for 906 Engineering Corp. It is not implied that any part listed is the product of these manufacturers.